Most viewed - Jetta Halogen90003 to HID Bi-Xenon |
![Filename=Bi-Xenon9003_001-a.jpg
Filesize=354KiB
Dimensions=1600x1200
Date added=Dec 04, 2010 Bi-Xenon9003_001-a.jpg](albums/Jetta_9003_to_HID/thumb_Bi-Xenon9003_001-a.jpg)
13683 viewsThe far left box shows plastic removed for the HID wires and the 3-prong plug that normally goes on the halogen bulb. Make the left [driver] side slightly bigger to accommodate all wires. Should be snug! Center box shows how bulb retaining hook is moved to under the frame and the far right box shows how the retaining wire is positioned to hold the HID bulb in. It will require a slight bending of the wire but not too much because you don't want to break the spring steel!!
|
|
![Filename=Bi-Xenon9003_003.jpg
Filesize=268KiB
Dimensions=1600x1200
Date added=Dec 04, 2010 Bi-Xenon9003_003.jpg](albums/Jetta_9003_to_HID/thumb_Bi-Xenon9003_003.jpg)
23620 viewsHere's the wiring pushed down in the slot and ready for the cover to be placed on. Note that on the right [passenger] side there was no need for the bulb plug so I left it inside the light housing and made the wire pass-through notch big enough for just the HID wiring.
|
|
![Filename=Bi-Xenon9003_004.jpg
Filesize=446KiB
Dimensions=1600x1200
Date added=Dec 04, 2010 Bi-Xenon9003_004.jpg](albums/Jetta_9003_to_HID/thumb_Bi-Xenon9003_004.jpg)
33604 viewsThe left cover has been modified; the right has not. The covers are not "sided", they are the same so you don't have to worry about mixing them up. Modify them both the exact same way.
|
|
![Filename=Bi-Xenon9003_014.jpg
Filesize=443KiB
Dimensions=1600x1200
Date added=Dec 05, 2010 Bi-Xenon9003_014.jpg](albums/userpics/10001/thumb_Bi-Xenon9003_014.jpg)
10643 viewsRelay zip-tied to hose clamp on left [driver] side. Ballast/ignitor is under the light housing, on the longitudinal bumper frame(?), sitting on a pad.
|
|
![Filename=Bi-Xenon9003_007.jpg
Filesize=391KiB
Dimensions=1600x1200
Date added=Dec 04, 2010 Bi-Xenon9003_007.jpg](albums/Jetta_9003_to_HID/thumb_Bi-Xenon9003_007.jpg)
5630 viewsUse a sharp blade to score the plastic. This will allow the plastic to break away easily.
|
|
![Filename=Bi-Xenon9003_006.jpg
Filesize=378KiB
Dimensions=1600x1200
Date added=Dec 04, 2010 Bi-Xenon9003_006.jpg](albums/Jetta_9003_to_HID/thumb_Bi-Xenon9003_006.jpg)
4624 viewsCut out the plastic lip from the covers. This allows the cover to be placed back on and turned, helping to keep water and dust out of the light housing.
|
|
![Filename=Bi-Xenon9003_013.jpg
Filesize=462KiB
Dimensions=1600x1200
Date added=Dec 05, 2010 Bi-Xenon9003_013.jpg](albums/userpics/10001/thumb_Bi-Xenon9003_013.jpg)
9616 viewsRight [passenger] side ballast/ignitor affixed to airbox top.
|
|
![Filename=Bi-Xenon9003_010.jpg
Filesize=665KiB
Dimensions=1600x1200
Date added=Dec 04, 2010 Bi-Xenon9003_010.jpg](albums/Jetta_9003_to_HID/thumb_Bi-Xenon9003_010.jpg)
7596 viewsUse sharp blade to cut away the plastic and bevel the lip (remove sharp edges).
|
|
![Filename=Bi-Xenon9003_009.jpg
Filesize=457KiB
Dimensions=1600x1200
Date added=Dec 04, 2010 Bi-Xenon9003_009.jpg](albums/Jetta_9003_to_HID/thumb_Bi-Xenon9003_009.jpg)
6587 viewsUse pliers to gently pull the section back. Start from one end and work your way to the other end.
|
|
![Filename=Bi-Xenon9003_012.jpg
Filesize=311KiB
Dimensions=1600x1200
Date added=Dec 04, 2010 Bi-Xenon9003_012.jpg](albums/Jetta_9003_to_HID/thumb_Bi-Xenon9003_012.jpg)
8580 viewsThe end result. Removed material should almost be flush with the rubber sealing ring. It's okay and recommended to have it a bit higher than the sealing ring, say, .5mm to 1mm.
|
|
|
|
|